user manual – BC3010 Charging station

Knowledge Base > Products > Accessories > BC3010 > BC3010 Manual

Introduction

The BC3010 Charging Station is a 10-Tag charger for the BlueCats BC2611 Tag.

The Charging Station can fully charge a depleted Tag in less than six hours. The Charging Status LED on the SafetyTag blinks green while charging, then turns solid green when fully charged.

Up to four Charging Stations can be daisy-chained together off of one power supply, making infrastructure requirements minimal. Charging Stations can be wall or table-mounted to best suit your environment.

Figure 1. The BC3010 Charging Station

WARNING: Read through this entire User Manual before operating the product. Failure to follow the included instructions and safety warnings may result in damage to the product or other property.

Safety Information

Read and follow all instructions in this User Manual before using this product.

WARNING: Changes or modifications not expressly approved by BlueCats could void your authorization to operate this product.

  • Do not use the BC3010 Charging Station if it is damaged.
  • Do not install in environments that exceed temperature and humidity requirements.
    • Operating temperature: −20°C to +50°C
    • Storage temperature: −40°C to +85°C
    • Working humidity: 20−95%, non-condensing
    • Relative humidity: Up to 95%, non-condensing
  • Do not place or leave the Charging Station on a heat source.
  • Do not open the Charging Station. It does not contain any user-serviceable parts or replaceable parts.
  • Dispose of a non-functioning Charging Station in accordance with local regulations.
  • This product is intended to be used at an altitude <2000m.
  • This product’s classification is Pollution Degree 2.
  • The power supply cord is used as the disconnect to remove power from the device.

In the Box

  • BC3010 Charging Station
  • BC3010 power supply cable
  • BC3010 Daisy Chain cable
  • Mounting hardware
    • Large angled brackets (2)
    • Small flat brackets (2)
    • Machine screws (8)

Mounting Options

There are two installation configurations for the BC3010 Charging Station: table or wall-mounted. 

Table Mounting

To securely mount a BC3010 Charging Station to a table:

  1. Remove the Charging Station from the packing box. 

  2. Secure the Charging Station to the table using the provided small brackets and screws provided:

    1. Screw the small brackets (not the large, angled brackets) into the back of the Charging Station using the provided machine screws (Figure 2).

    2. Lay the Charging Station down on the table where desired, then screw the brackets into the table. 

  3. Attach the power supply cable to the power supply connector on the Charging Station (Figure 3).

  4. Plug the Charging Station into AC power using the provided power supply. 

Figure 2. Small bracket screwed into the back of the Charging Station.

Wall Mounting

To securely mount a BC3010 Charging Station to a wall:

  1. Remove the Charging Station from the packing box. 

  2. Attach the large angled brackets (not the small flat brackets) using the provided machine screws.

    Note: Install the angled brackets so that the Charging Station is tilted slightly up (Figure 4).

  3. Using secure mounting practices (screws into studs or drywall anchors), secure the Charging Station to the wall. 

  4. Attach the power supply cable to the power supply connector on the Charging Station (Figure 3).

  5. Plug the Charging Station into power using the provided power supply.

Figure 4. Large angled brackets ensure the Charging Station tilts up.

Figure 5. A wall-mounted Charging Station.

Daisy-Chaining (Table or Wall Mount)

Up to four BC3010 Charging Stations can be daisy-chained together to receive power from a single power supply. You can daisy-chain Charging Stations in either the table or wall-mounted configuration.

Note: No more than four Charging Stations may be connected to a single power supply.  

To securely daisy-chain Charging Stations:

  1. If desired, attach the provided flat metal brackets to the side mounting location on the back of each Charging Station in the chain. These brackets can secure the Charging Stations to each other.
  2. Connect the Daisy Chain cable to the Daisy Chain connector on the first Charging Station, which should be connected to the power supply (as shown on the left Charging Station in Figure 6).
  3. Connect the other end of the Daisy Chain cable to the power supply connector on the second Charging Station (the right Charging Station in Figure 6).
  4. As needed, create a chain of up to four total Charging Stations by connecting additional Daisy Chain cables to subsequent Charging Stations as done in steps 1-3.

Operating Instructions

To charge a BC2611 SafetyTag, place it securely within one of the available slots on a powered Charging Station. The Charge LED on the SafetyTag will blink green while charging, and turn solid green when completely charged. The Charging Station can charge a total of 10 SafetyTags.

BlueCats Support

We’re here to help. If you need any assistance, please contact us for technical support via the BlueCats Support site. We also welcome your questions and suggestions to improve your experience with our products.

Regulatory Information

FCC

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

IC

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS) d’Innovation, Sciences et Développement économique Canada. Le fonctionnement est soumis aux deux conditions suivantes : (1) Cet appareil ne doit pas causer d’interférences. (2) Cet appareil doit accepter toutes les interférences, y compris celles susceptibles de provoquer un fonctionnement indésirable de l’appareil.

Navigation